msa-gauge-rr
Measurement System Analysis (MSA) and Gauge Repeatability & Reproducibility (Gauge R&R) — plan, execute, and interpret an MSA study for variable or attribute measurement systems. Use when qualifying a gauge for a new part, validating a measurement system before PPAP, interpreting Gauge R&R results, or auditing MSA studies for adequacy. Covers AIAG MSA 4th edition.
- License 许可
- MIT
- 最近更新
- 2026-11-14
- Stars
- ★ 1.6k
- Forks
- 491
01 前言 Front Matter
- name
- msa-gauge-rr
- license
- MIT
- metadata
- { "author": "RBraga01", "domain": "quality-engineering", "status": "approved", "created": "2026-06-06", "version": "1.1", "iso-9001": "7.1.5", "subdomain": "measurement", "iatf-16949": "7.1.5.1, 7.1.5.2", "industries": "automotive,electronics,aerospace,medical,general", "updated_by": "migmcc", "reviewed_by": "RBraga01", "last_updated": "2026-06-06", "aiag-reference": "AIAG MSA 4th Edition", "standard_edition": "AIAG MSA 4th Edition (2010)" }
- description
- Measurement System Analysis (MSA) and Gauge Repeatability & Reproducibility (Gauge R&R) — plan, execute, and interpret an MSA study for variable or attribute measurement systems. Use when qualifying a gauge for a new part, validating a measurement system before PPAP, interpreting Gauge R&R results, or auditing MSA studies for adequacy. Covers AIAG MSA 4th edition.
02 资源文件 1
- 参考文档references/gauge-rr-study-guide.md15.4 KB
03 SKILL.md 正文
Measurement System Analysis (MSA) / Gauge R&R
When to use
Use this skill when:
- Qualifying a measurement system for a new part or process (PPAP requirement)
- Interpreting Gauge R&R results — is this gauge acceptable?
- Auditing a supplier's MSA study for correctness and adequacy
- Selecting the right study type for a given measurement situation
- Investigating a quality problem where measurement error may be a factor
- Responding to a customer request for MSA data on a specific characteristic
Prerequisites
- The characteristic to be measured (product or process)
- The gauge or measurement system to be studied
- Production parts spanning the expected process variation (10 parts minimum)
- At least 2 trained appraisers who normally perform the measurement
- The specification (tolerance) for the characteristic
Workflow
Step 1 — Select the MSA study type
| Study type | When to use |
|---|---|
| Gauge R&R (crossed) | Variable data, 2–3 appraisers, each measures all parts (most common) |
| Gauge R&R (nested) | Variable data, parts are destroyed during measurement (e.g., tensile test) |
| Attribute MSA | Pass/fail, go/no-go, visual inspection — data is not a number |
| Bias study | Accuracy of a single gauge vs. a reference standard |
| Linearity study | Whether gauge accuracy is consistent across its measurement range |
| Stability study | Whether gauge accuracy drifts over time |
For PPAP: Crossed Gauge R&R is required for all variable gauges on special characteristics.
Step 2 — Crossed Gauge R&R study procedure
Setup:
- Minimum 10 parts selected to represent the full process variation range (not cherry-picked from centre of tolerance)
- Minimum 2 appraisers (3 preferred)
- Minimum 2 trials per appraiser per part (3 preferred)
- Parts randomly numbered and labelled — appraisers must not see each other's measurements
- Measurement conditions must match normal production conditions
Standard study design:
- 10 parts × 3 appraisers × 2 trials = 60 measurements
- 10 parts × 2 appraisers × 3 trials = 60 measurements
Execution:
- Appraiser A measures all 10 parts in random order — record results
- Appraiser B measures all 10 parts in random order — record results
- Appraiser C measures all 10 parts in random order — record results
- Repeat the cycle for trial 2 (and trial 3 if applicable)
- Appraisers must not see their own previous results or other appraisers' results during the study
Do NOT:
- Allow appraisers to adjust the gauge between trials
- Use parts that are all near the nominal value (no spread)
- Record only one trial (single measurement per appraiser per part is insufficient)
Step 3 — Interpret the results
%GRR (Gauge R&R as % of Total Variation or % of Tolerance)
| %GRR | Interpretation | Decision |
|---|---|---|
| < 10% | Excellent | ✅ Gauge accepted |
| 10% – 30% | Marginal | ⚠️ May be acceptable based on application — requires engineering review and customer approval |
| > 30% | Unacceptable | ❌ Gauge not suitable — investigate and improve before use in production |
Two calculation methods:
- % of Study Variation (% of TV): GRR / Total Variation × 100 — preferred when process is in control
- % of Tolerance: GRR / Tolerance × 100 — use when process capability is unknown or for attribute gauging
For PPAP, %GRR < 30% (tolerance method) is the typical customer acceptance criterion. <10% is the target.
Number of Distinct Categories (ndc)
ndc = 1.41 × (Part Variation / GRR)
| ndc | Interpretation |
|---|---|
| ≥ 5 | ✅ Gauge can distinguish adequate number of categories |
| 3 – 4 | ⚠️ Gauge can be used for go/no-go decisions only |
| 1 – 2 | ❌ Gauge cannot distinguish parts — unacceptable |
ndc ≥ 5 is required for measurement systems used on special characteristics.
Repeatability vs. Reproducibility
| Component | Description | Common cause |
|---|---|---|
| EV (Equipment Variation / Repeatability) | Variation when same appraiser measures same part multiple times | Gauge imprecision, worn parts, environment |
| AV (Appraiser Variation / Reproducibility) | Variation between different appraisers measuring the same part | Training inconsistency, measurement technique, gauge setup |
If EV > AV: investigate gauge (calibration, maintenance, resolution) If AV > EV: investigate training, measurement procedure, gauge fixture/setup
When %GRR > 30% — improving the measurement system
A result >30% means the gauge is not suitable for production use. Do not proceed to PPAP — investigate and retest. Common root causes and actions:
| Root cause (high EV) | Action |
|---|---|
| Gauge resolution too coarse | Replace with a gauge of finer resolution (rule: resolution ≤ 10% of tolerance) |
| Gauge worn or damaged | Inspect, recalibrate, or replace the gauge |
| Environmental interference (vibration, temperature) | Move measurement to a stable environment; add fixture if needed |
| Inconsistent part fixturing | Design a repeatable fixture or measurement aid |
| Root cause (high AV) | Action |
|---|---|
| Measurement technique varies by appraiser | Develop a standardised measurement instruction (WI with photos/video) |
| Gauge difficult to read or position | Redesign fixture; add a datum locator; use a self-positioning gauge |
| Training gap | Retrain all appraisers using the standardised measurement WI; repeat the study |
After implementing improvements: re-run the full study. Do not accept a %GRR > 30% result with a customer waiver unless the characteristic is non-critical and the customer explicitly agrees in writing.
Step 4 — Attribute MSA (pass/fail gauges)
For go/no-go gauges, visual inspection, and any pass/fail decision:
Expanded attribute study (recommended for PPAP):
- 50 parts spanning the full range (include parts near the accept/reject boundary)
- 3 appraisers × 3 trials per part = 450 measurements
- Calculate % agreement (within appraiser and between appraisers)
- Calculate kappa statistic (Cohen's kappa ≥ 0.9 is acceptable)
Short method (minimum acceptable):
- 20 parts × 2 appraisers × 2 trials
- 90% agreement within and between appraisers required
- Include borderline parts near the specification limit
Step 5 — Audit an existing MSA study
When reviewing a supplier's or internal MSA, check:
- [ ] Parts selected represent the full process variation range (not all near nominal)
- [ ] Minimum 10 parts, 2 appraisers, 2 trials confirmed
- [ ] Appraisers did not see each other's or their own previous results
- [ ] %GRR result stated clearly (tolerance method or study variation method — which one?)
- [ ] ndc ≥ 5 for all special characteristics
- [ ] EV vs. AV breakdown analysed and interpreted
- [ ] %GRR < 30% (conditional: <10% preferred)
- [ ] For attribute gauges: kappa statistic calculated
- [ ] Study performed in production conditions (not in metrology lab if production measurement is on the line)
- [ ] Gauge calibration certificate current at time of study
Validation criteria
An MSA study is acceptable for PPAP when:
- %GRR < 30% (tolerance method) — <10% preferred
- ndc ≥ 5
- Study conducted with production appraisers using production gauges in production conditions
- Parts selected from the full process variation range
- Results documented with part numbers, appraiser IDs, gauge ID, and calibration reference
Common mistakes
- Parts selected near the nominal value only — artificially inflates ndc and understates GRR
- Appraiser A re-measures all parts immediately — not the same as separate trials (must separate in time)
- Using metrology lab gauges for an MSA of a production line gauge — study must use the same gauge in the same conditions
- %GRR > 30% submitted in PPAP without explanation or customer waiver
- Gauge calibration expired at time of MSA study — study is invalid
- ndc < 5 on a special characteristic — automatic PPAP finding in IATF audits
- Attribute MSA with only 2 appraisers and no borderline parts — study has no discriminating power
Output Format
At the start of each use, ask the user:
"How would you like to receive the output? A — Structured Markdown (formatted tables and sections, ready to copy) B — Plain tables (simplified structure for Excel or Word) C — Narrative report (flowing text for a formal document or email)
Default: A."
Adapt all output sections to the chosen format. If the platform or session context already defines a format preference, skip this question.
Changelog
| Version | Date | Author | Change |
|---|---|---|---|
| 1.0 | 2026-06-06 | @RBraga01 | Initial release |
| 1.1 | 2026-06-06 | @migmcc | Added improvement guidance for %GRR > 30% — root cause table for high EV and high AV with corrective actions |
04 同仓库更多 Skills
worktable-review-with-annotations
Create, inspect, reply to, update, or resolve situated Worktable annotations. Use when feedback belongs to a Doc section, block, text range, or HTML Doc, or when the user asks to address existing review feedback and coordinate a requested artifact edit.
worktable-find-and-synthesize-context
Find, assess, and synthesize context from Worktable Docs and Records. Use when the user asks what a workspace contains, wants workspace-backed research, needs current facts reconciled across artifacts, or requests a cited synthesis without changing workspace state.
worktable-create-or-update-docs
Create, edit, rename, or maintain narrative Worktable Docs. Use for plans, decisions, briefs, notes, research syntheses, and other durable prose when the user requests a new artifact or a safe update to an existing one.
worktable-create-or-manage-records
Organize repeated structured information as durable Worktable Records. Use for research datasets, inventories, directories, pipelines, trackers, and other collections whose items need identity, fields, filtering, links, validation, or individual updates.
worktable-create-or-manage-interactive-html
Create or improve durable visual and interactive artifacts in Worktable. Use for dashboards, trackers, calculators, mini apps, slide presentations, and other requests that benefit from a polished HTML Doc.
worktable-collaborate-threads
Read, answer, and hand off messages through durable Worktable threads with users or other authenticated participants. Use when the user asks to check addressed messages, reply to a participant, continue a thread, request another agent's help, wait briefly for a response, or watch for comments and messages sent to the agent.